Safety Function Manual for Collaborative Robot
English
English
  • Safety Function Manual for Collaborative Robot
  • About this manual
    • Copyright
    • Notation rules
    • Safety precautions
  • 1. Safety functions of the collaborative robot
    • 1.1 Description of terms
    • 1.2 Collaborative operation mode
      • 1.2.1 Safety-rated monitored stop
      • 1.2.2 Hand guiding
      • 1.2.3 Speed and separation monitoring
      • 1.2.4 Power and force limiting
    • 1.3 Safety functions
      • 1.3.1 Robot limit functions
      • 1.3.2 Joint limit functions
    • 1.4 Matters to be checked upon replacing safety devices
    • 1.5 Matters to be checked before using the safety functions
      • 1.5.1 Encoder offset
      • 1.5.2 Checking the torque sensor
        • 1.5.2.1 Torque sensor offset
      • 1.5.3 Setting of tool data
      • 1.5.4 Password setting
    • 1.6 Robot safety conditions
      • 1.6.1 Robot limiting parameters
      • 1.6.2 Joint limiting parameters
    • 1.7 Safety layout
      • 1.7.1 Safety space setting
        • 1.7.1.1 Setting information on safety space parameters
      • 1.7.2 Safety tool modeling
      • 1.7.3 Safety robot modeling
      • 1.7.4WorkCell 3D
    • 1.8 Safety I/O signals
    • 1.9Safety Stop Function
    • 1.10 Safety condition monitoring
      • 1.10.1 Robot limiting parameter monitoring
      • 1.10.2Joint limiting function monitoring
      • 1.10.3 SCM board status monitoring
      • 1.10.4 Safety I/O status monitoring
      • 1.10.5 Recovery mode
        • 1.10.5.1 Recovery in case of robot position violations
        • 1.10.5.2 Recovery in case of robot speed violations
        • 1.10.5.3 Recovery in case of robot force violations
        • 1.10.5.4 Recovery in cases of safe operating stop (SOS) violations
    • 1.11 Collaborative robot collision detection mode
  • 2. Direct teaching
    • 2.1 Direct teaching switch assignment
    • 2.2 Driving the robot by direct teaching
    • 2.3 Direct teaching mode setting
    • 2.4 Constraint motion
  • 3. I/O setting
    • 3.1 I/O map
    • 3.2 Tool I/O
      • 3.2.1 Default specifications of the tool I/O
      • 3.2.2 Tool I/O setting
    • 3.3 Analog I/O
      • 3.3.1 Default specifications of the analog I/O
      • 3.3.2 Analog I/O setting
  • 4. Error messages
    • E7001~E7066
    • E7101~E7120
    • E7170~E7213
    • E7250~E7348
    • E7403~E7711
    • E7731~E7905
  • Attachment
    • The Rules on the Criteria for Occupational Safety and Health, and the Public Notice of Safety Inspec
  • Warranty
Powered by GitBook
On this page

Was this helpful?

  1. About this manual

Copyright

All the programs, files, and contents relating to this product and manual are protected by the Copyright Act and a confidentiality agreement. Any use, reproduction, and disclosure or distribution of this manual to third parties not explicitly permitted by Hyundai Robotics are strictly prohibited.

Copyright ⓒ 2020 HYUNDAI ROBOTICS. All rights reserved.

PreviousAbout this manualNextNotation rules

Last updated 3 years ago

Was this helpful?