Maintenance Manual for Collaborative Robot
English
English
  • Maintenance Manual for Collaborative Robot
  • About this manual
    • Copyright
    • Notation rules
    • Safety precautions
  • 1. Safety
    • 1.1 Safety requirements
      • 1.1.1 Applicable standards
      • 1.1.2 Safety performance
    • 1.2 Safety measures
      • 1.2.1 Safety functions
      • 1.2.2 Safety training
      • 1.2.3 Safety labels
      • 1.2.4 Emergency stop
        • 1.2.4.1 Emergency stop switches
        • 1.2.4.2 Connecting to emergency stop devices of external systems
    • 1.3 Risk assement
    • 1.4 Potential risk
    • 1.5 Validity and responsibilities
  • 2. Introduction to the product
    • 2.1 Intended uses of the product
    • 2.2 Product components
    • 2.3 Part names
      • 2.3.1 Manipulator
      • 2.3.2 Controller
      • 2.3.3 Teach pendant
    • 2.4 Nameplate
  • 3. Product installation
    • 3.1 Environment of installation and preparation
      • 3.1.1 Environments of installation and use
      • 3.1.2 Spaces of the robot system
      • 3.1.3 Allowable limit of wrist axis load
      • 3.1.4 Payload
    • 3.2 Product installation
      • 3.2.1 Composition of robot systems
      • 3.2.2 Robot and controller installation
        • 3.2.2.1 Mounting plate installation
      • 3.2.3 Tool connection
      • 3.2.4 Wiring
      • 3.2.5 Power on
    • 3.3 Robot interface
      • 3.3.1 Tool flange connection point
        • 3.3.1.1 T4071017041-001 (TE) pin map
        • 3.3.1.2 T41171130012-001 (TE) pin map
        • 3.3.1.3 Air hose
      • 3.3.2 External device interface
        • 3.3.2.1 Terminal block (TB1): common analog I/O signals
        • 3.3.2.2 Terminal block (TB2): dedicated safety signal input
        • 3.3.2.3 Terminal block (TB3): system signal I/O
        • 3.3.2.4 D-sub 25-pin connector (SDIO): common digital I/O
        • 3.3.2.5 D-sub 9-pin connector (COM1, COM2): serial communication (RS485, 422)
    • 3.4 Stopping distance and time
      • 3.4.1 STOP 0
      • 3.4.2 STOP1
    • 3.5 Safety setting
    • 3.6 Programming and restarting
    • 3.7 Axis limiting devices
    • 3.8 Movement without drive power
    • 3.9 Other safety precautions
  • 4. Maintenance
    • 4.1 Checking of the collaborative robot
      • 4.1.1 Check sheet
      • 4.1.2 Wiring check
      • 4.1.3 Bolt check
    • 4.2 Maintenance of the collaborative robot
      • 4.2.1 Replacement of internal wiring
      • 4.2.2 Replacement of the integrated driving module
        • 4.2.2.1 Replacement timing
        • 4.2.2.2 Weight of the integrated driving module
        • 4.2.2.3 Tools and parts
        • 4.2.2.4 Recommended posture in disassembling the integrated driving module
        • 4.2.2.5 Method for replacing the integrated driving module
      • 4.2.3 Encoder backup battery replacement
      • 4.2.4 Grease replacement
    • 4.3 Controller check and maintenance
      • 4.3.1 Internal structure
      • 4.3.2 Safety control module
        • 4.3.2.1 Connection and display
        • 4.3.2.2 Connection of I/O signals for the robot system (TBSYS1)
        • 4.3.2.3 Safety I/O signal connection (TBSDI, TBSDO)
        • 4.3.2.4 Connection of common digital I/O signals (TBDIO)
        • 4.3.2.5 Connection of common digital I/O signals (TBAIO)
        • 4.3.2.6 Information on major components
      • 4.3.3 Power precharge module (PPM)
        • 4.3.3.1 Connection and display
        • 4.3.3.2 Information on major components
      • 4.3.4 Regenerative discharge module (RDM)
        • 4.3.4.1 Connection and display
        • 4.3.4.2 Information on major components
      • 4.3.5 Microcomputer module
      • 4.3.6 Power supply
      • 4.3.7 Teach pendant
      • 4.3.8 PCI communication card (optional)
        • 4.3.8.1 Connect pin map
  • 5. Moving and storing
    • 5.1 Moving method
      • 5.1.1 Recommended posture
      • 5.1.2 Packaging box
      • 5.1.3 Cautions
    • 5.2 Storing method
    • 5.3 Disposal
  • 6. Appendix
    • 6.1 Block diagrams
      • 6.1.1 YL012 S-axis
      • 6.1.2 YL012 H-axis
      • 6.1.3 YL012 V-axis
      • 6.1.4 YL012 R-axis
      • 6.1.5 YL012 B-axis
      • 6.1.6 YL012 R1-axis
      • 6.1.7 YL012 tool flange
      • 6.1.8 Power connector
    • 6.2 System specifications
      • 6.2.1 Collaborative robot
      • 6.2.2 Controller
      • 6.2.3 Teach pendant
  • Certifications
  • Attachment
    • Rules on Occupational Safety and Health Standards, and Notice for Safety Inspection
  • Quality Assurance
Powered by GitBook
On this page

Was this helpful?

  1. 4. Maintenance
  2. 4.2 Maintenance of the collaborative robot

4.2.1 Replacement of internal wiring

Check the internal wiring of the collaborative robot at three-month intervals. Check on damaged wires, cables, and cable-protecting springs, and replace any defective parts immediately.

  • The wiring replacement intervals vary depending on operating conditions, the robot’s operating speed, and how long the robot operates continuously.

  • Regardless of the major operation and operating conditions of the robot, replace the cables at the intervals of 16,000 hours.

  • Replace wires in units.

  • Wiring between the collaborative robot and the controller must be carried out in the specified length.

[Caution]

  • The internal wiring should be done with cables of bending resistance. Only use cables of the specified types.

  • For purchasing an internal cable, identify the wiring type by consulting with our Customer Support Team.

  • Before replacing cables, cable-protecting springs, or hoses, check that the replacement parts are not broken or damaged.

Previous4.2 Maintenance of the collaborative robotNext4.2.2 Replacement of the integrated driving module

Last updated 3 years ago

Was this helpful?