Safety Function Manual for Collaborative Robot
English
English
  • Safety Function Manual for Collaborative Robot
  • About this manual
    • Copyright
    • Notation rules
    • Safety precautions
  • 1. Safety functions of the collaborative robot
    • 1.1 Description of terms
    • 1.2 Collaborative operation mode
      • 1.2.1 Safety-rated monitored stop
      • 1.2.2 Hand guiding
      • 1.2.3 Speed and separation monitoring
      • 1.2.4 Power and force limiting
    • 1.3 Safety functions
      • 1.3.1 Robot limit functions
      • 1.3.2 Joint limit functions
    • 1.4 Matters to be checked upon replacing safety devices
    • 1.5 Matters to be checked before using the safety functions
      • 1.5.1 Encoder offset
      • 1.5.2 Checking the torque sensor
        • 1.5.2.1 Torque sensor offset
      • 1.5.3 Setting of tool data
      • 1.5.4 Password setting
    • 1.6 Robot safety conditions
      • 1.6.1 Robot limiting parameters
      • 1.6.2 Joint limiting parameters
    • 1.7 Safety layout
      • 1.7.1 Safety space setting
        • 1.7.1.1 Setting information on safety space parameters
      • 1.7.2 Safety tool modeling
      • 1.7.3 Safety robot modeling
      • 1.7.4WorkCell 3D
    • 1.8 Safety I/O signals
    • 1.9Safety Stop Function
    • 1.10 Safety condition monitoring
      • 1.10.1 Robot limiting parameter monitoring
      • 1.10.2Joint limiting function monitoring
      • 1.10.3 SCM board status monitoring
      • 1.10.4 Safety I/O status monitoring
      • 1.10.5 Recovery mode
        • 1.10.5.1 Recovery in case of robot position violations
        • 1.10.5.2 Recovery in case of robot speed violations
        • 1.10.5.3 Recovery in case of robot force violations
        • 1.10.5.4 Recovery in cases of safe operating stop (SOS) violations
    • 1.11 Collaborative robot collision detection mode
  • 2. Direct teaching
    • 2.1 Direct teaching switch assignment
    • 2.2 Driving the robot by direct teaching
    • 2.3 Direct teaching mode setting
    • 2.4 Constraint motion
  • 3. I/O setting
    • 3.1 I/O map
    • 3.2 Tool I/O
      • 3.2.1 Default specifications of the tool I/O
      • 3.2.2 Tool I/O setting
    • 3.3 Analog I/O
      • 3.3.1 Default specifications of the analog I/O
      • 3.3.2 Analog I/O setting
  • 4. Error messages
    • E7001~E7066
    • E7101~E7120
    • E7170~E7213
    • E7250~E7348
    • E7403~E7711
    • E7731~E7905
  • Attachment
    • The Rules on the Criteria for Occupational Safety and Health, and the Public Notice of Safety Inspec
  • Warranty
Powered by GitBook
On this page

Was this helpful?

  1. 1. Safety functions of the collaborative robot
  2. 1.10 Safety condition monitoring

1.10.5 Recovery mode

Previous1.10.4 Safety I/O status monitoringNext1.10.5.1 Recovery in case of robot position violations

Last updated 3 years ago

Was this helpful?

In recovery mode, you can clear errors that occur because of the safety function violations during monitoring. Because position detection is temporarily disabled in recovery mode, you can drive the robot and adjust its angle and position without violating the safety functions.

If a safety function monitoring is violated, the robot will activate a safety stop immediately and stop moving. In addition, the safety stop notice window will appear on the operating program window.

1 .Set the operating mode to the manual mode.

2. On the safety stop notice window, click the [ENTER] button. Then, the safety condition monitoring window will appear.

3. Click the [Status Recovery] button. Then, the [Status Recovery] button will turn green, and the system will enter recovery mode.

4. In recovery mode, adjust the robot’s angle and position to clear errors.

5. After the recovery is completed, click the [Status Recovery] button. Then, the [Status Recovery] will turn into the previous color, and the recovery mode will be cleared.

  • You can also clear the recovery mode by clicking the [X] button at the upper-right corner of the safety condition monitoring window.

[Caution]: After clearing the recovery mode, recheck the safety layout setting and the teaching position of the operating program.